Industrial Premier Brush Strip 25 mm Brush 34 mm Carrier

DRAUGHT PROOFING BRUSHES

OUR BRUSH IS MADE FROM GENUINE NYLON 6 BRISTLES ONLY TO FULL FILL STRIP.

WE DONT SELL POLYPROPYLENE FILAMENTS WE SELL NYLON 6

WE DONT PART FILL OUR BRUSHES

Draught Proof now before winter, Keep all the MICE out!

Seals by George Culley, called The Hairy Worm Industrial Premier Strip

These are made and supplied at any cut length.

up to 1100 mm these can go budget Hermes carrier, above this length TNT EXPRESS is only the option

We make them these cut length to allow you to easily trim these to the correct sizes to suit your door, if you are fitting to a long run multiple lengths can be used side by side with little loss of sealing benefit. When fitting under the soffit against a roller shutter, it is easier handling with shorter pieces a metre or so, so you are not swinging something too big/long at height!

Tip: whilst on about shutter doors, get the maximum gap with the door in a closed position to seal against an outer lath, if it goes in you may need to pack the brush out to get the best seal, or a lot of pressure is added to the door when opening and closing the door with the brush too tight.

(Whilst this range seal up to 150 mm, we do make bigger Industrial Premier Strip and make a thicker industrial range from 125 to 300 mm, MADE TO ORDER ONLY AT THOSE SIZES). We have access to many different styles of brush.

IN BULK WE CAN ALSO SUPPLY 3000 MM LENGTHS (MAXIMUM) MADE TO ORDER, PHONE 0161 622 0020

Please choose the correct size brush for your sealing project:

25 mm size is for fine draught proofing from 0 - 24 mm gaps (we also make smaller seals)

35 mm size is for fine draught proofing from 0 - 33 mm gaps

50 mm size is for fine draught proofing from 0 – 48 mm gaps

75 mm size is for fine draught proofing from 0 - 73 mm gaps

100 mm size is for fine draught proofing from 0 - 98 mm gaps

150 mm size is for fine draught proofing from 0 - 148 mm gaps

TIP: You may have a worn stone step IN A CHURCH OR OLDER HOME  50 mm is a good answer to this problem

 WE CAN GO BIGGER IN STRIP IF REQUIRED, PLEASE ASK

 THIS IS A UK MADE PRODUCT WE ARE PROUD OF MACHINED AND FINISHED IN ROCHDALE AND IS USED BY DOOR REPAIR COMPANIES AND GENERAL INDUSTRY.

All Brushes on Up & Over doors are to be fitted on the outside ONLY!

we suggest this because if you fit a brush on the front of a garage door as you lift the door (or the motor lifts a door) the filaments pull off the floor, if you fit it on the rear of the garage door, the brush is further swept tightening into the floor, straining all the door and also if fitted your motor. The other point is any rubbish blown under your door is blown into the garage.

It is easy to fit, just follow the simple instructions included, then THEHAIRYWORM Will give you a long life.

IF YOU NEED OTHER SIZES PLEASE ASK, OTHER TRIMS ARE AVAILABLE ON OUR SITE www.georgeculley.co.uk or www.thehairyworm.co.uk

This correctly made brush strip is not an import, this is made in the UK with pride.

MATERIALS:

We make a full fill brush with the right selected components. This range is using our 8 mm series backing width brush. Our brushes are made with nylon 6 Filaments; an important factor we feel.

The carrier is made from Architectural Aluminium a point worth noting, it makes the carrier stronger, its overall height is of the flat part of the "h" holder being 34 mm, the trim of brush is measured out of the steel backing inside the aluminium on this sizing giving about 2 mm of bristle less on all sizes out of the aluminium holder.

For the technically minded:

• Nylon 6 is a harder wearing material against concrete and other hardwearing surfaces than polypropylene
• Nylon 6 has a higher working temperature of about 165 degrees centigrade, Polypropylene softens far earlier than this.
• We do not use Polypropylene but competitors do, it softens at 70 – 80 degrees centigrade. This is a temperature your garage door reaches when it gets warm in the summer, when warm polypropylene bristles bend and stay bent causing the brush to appear to move away from its opposing surface, as they cool they stay the same size curled not touching the opposite side.

I will leave you to decide which is the right choice, I will say chalk and cheese! 

(A lot of competitors use these filaments and also partial fill! to make brushes lower in cost for them! OR SOME ARE NOW SELLING SAME SIZE CARRIER BUT ONLY 6 MM BRUSH, AT LEAST 30% LESS FILL, BUT FROM ABOVE THEY LOOK THE SAME.

• We don’t short change.

The brush strip should only be fitted to the outside of an up and over door, as the rear of the door dips slightly upon lifting up, if you put a brush or any seal on the bottom inside, it will catch and scrap causing the door to judder on opening, a problem if you have motor driven doors as it will strain and may become damaged.

 This item is suitable for draught proofing, dust sealing, dust sealing, insect sealing, stops flies, stops moths, Birds cockroaches yes they are in the UK, aluminium, timber, steel, PVCu, GRP doors,

We have also developed and have on sale "The Hairy Worm" a woven brush pile seal to go up the sides of an up and over door, please look on our shop~ CHECK THIS NEW ITEM OUT, 10,000+ Metres sold on EBAY!

 Culley’s also stock a large range of other style draught excluders, brush strips & weather strip products and also trade rubber extrusions.

Please enquire: TELEPHONE: 0161 622 0020 IF YOU NEED FREE ADVICE.

For correct advice for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.

DON’T HEAT THE STREET, SAVE £’S

Regardless of the number of pieces you buy, this product is shipped by a carrier called MYHERMES They take about 3-5 Working days from despatch, SO PLEASE ALLOW THE TIME FOR SHIPPING, IF YOUR ORDER IS A PANIC PLEASE RING 0161 622 0020 AND ARRANGE TNT, IT STILL TAKES 2-3 WORKING DAYS TO GET REDY FOR DESPATCH

IF THE WEATHER TURNS, PLEASE BEAR IN MIND DOZENS OF PEOPLE ONLY NOTICE DRAUGHTS WHEN IT GETS COLD AND THE HEATING IS CRANKED UP, WE DO GET BUSY, SO THERE COULD BE DELAYS 

 We are able to ship this item only to British Post Codes

Cuts easily with small bolt cropper style top hardened cutters, and a good hacksaw, comes with full fitting instructions, you need to follow the full instructions

WE DO NOT SUPPLY SCREWS AS WE KNOW DIFFERENT SURFACES REQUIRE DIFFERENT FIXINGS AND DIFFERENT COLOURS, AGAIN WE DO NOT DRILLTHE PRODUCT AS ALL THE HOLES WILL NOT LINE UP WITH YOUR DOOR.