Door draught excluder brush strip sweeper 22mm Nylon 6 22 mm trim x 890 mm
WE SEND THIS BY MY HERMES TAKING 3 TO 5 WORKING DAYS AFTER OUR 1-3 WORKING DAYS TO ASSEMBLE,IE STANDARD IS 4 TO 8 WORKING DAYS TO DELIVERY IF THE WEATHER CHANGES BAD IN WINTER .................WE GET BUSY AND DELAYS DO HAPPEN , PLEASE BEAR WITH US
draught proof now before winter comes (if it does this year)
KEEP THE MICE OUT
THIS IS A 890 mm section or in old money 35" and will be long enough for most UK doors
GAP SIZE 0 – 20 MM
THIS UK MADE PRODUCT IS MADE BY THE HAIRY WORM IN ROCHDALE (Mathews dad !)
& USED BY THE DOOR REPAIR INDUSTRY for domestic doors with a flat step under neath
instructions for correct cutting included , please follow
( TO FIT DOWN THE BOTTOM OF AN UP AND OVER GARAGE DOOR YOU WILL NEED TO ORDER MORE LENGTHS )
TYPICALLY TO SEAL FROM 2.000 METRES UP TO 2.670 METRES , ( 7 FEET TO 8 FEET 9“ Maximum width ) YOU WILL NEED THREE PIECES FOR A STANDARD GARAGE DOOR
IF YOU NEED OTHER SIZES PLEASE ASK, OTHER TRIMS ON OUR CULLEY_FAMILY_SHOP
This correctly made brush strip is not an import; this is made in the UK with pride
We make a full fill brush with the right components. This is our 4 mm series backing width brush
Our brushes are made of nylon 6 an important factor we feel.
The carrier is made from architectural aluminium a point worth noting, it makes the carrier stronger, its overall height of the flat part of the h holder is 16 mm, the trim of brush is 22 mm out of the steel backing inside the aluminium on this sizing giving about 20 mm of bristle out of the aluminium holder.
We supply this part in 890 mm long so the item can be my hermes COURIERED to any UK postcode, except Scotland Highlands and Islands, please ask for a carriage rate outside this area
for the technically minded , nylon 6 is a harder wearing material against concrete than polypropylene Nylon 6 has a higher working temperature of about 145 degrees centigrade
We do not use Polypropylene but competitors do , it softens at 70 – 80 degrees centigrade. A temperature your garage door reaches when it gets warm in the summer , polypropylene bristles then bend and stays bent causing the brush to appear to move away from its opposing surface, I will leave you to decide which is the right choice , I will say chalk and cheese!
(A lot of competitors use this and also partial fill! to make brushes lower in cost for them!)
The brush strip should only be fitted to the outside of an up and over door , as the rear of the door dips slightly upon lifting , if you put a brush or any seal on the bottom ,it will catch and scrap causing the door to judder on opening , a problem if you have motor driven doors.
This item is suitable for draught proofing , dust sealing , dust sealing , insect sealing , stops flies , stops moths , cockroaches yes they are in the UK, ,aluminium,t imber ,steel , PVCu, GRP doors,
Cuts easily with top hardened cutters, or good pincers and junior hacksaw, comes with full fitting instructions, you need to follow the full instructions
WE DO NOT SUPPLY SCREWS AS WE KNOW DIFFERENT SURFACES REQUIRE DIFFERENT FIXINGS AND DIFFERENT COLOURS, AGAIN WE DO NOT DRILLTHE PRODUCT AS ALL THE HOLES WILL NOT LINE UP WITH YOUR DOOR.
We have also developed and have on sale "thehairyworm" seal to go up the sides of an up and over door ,please look on our shop, SMALLER SIZES FOR SLIDING SASH WINDOWS AND OTHER STYLES OF WINDOWS
Culley’s also stock a large range of other style draught excluders, brush strips & weather strip products and also trade rubber extrusions.
Please enquire. Via e bay questions for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.
DON’T HEAT THE STREET, SAVE IT!!! ITS YOUR MONEY
If you require more info please contact me on: 0161 622 0020