Call - 0161 622 0020
Cart 0
GOOD door draught excluder sealing strip kit 15 mm long brush 1 @ 1100 mm

GOOD door draught excluder sealing strip kit 15 mm long brush 1 @ 1100 mm

£14.99

We supply this part in 1 off pieces @ 1100 MM long so the item can be COURIERED  BY "MYHERMES" to MOST UK postcodes inc NI , But EXCL SCOTTISH ISLES AND CHANNEL ISLANDS

 

PLEASE ALLOW 3 DAYS TO DESPATCH AND 3 TO 4 WORKING DAYS TO DELIVER IE 5-7 WORKING DAYS TO DELIVERY , WE HAVE A LOT OF STOCK BUT WE ENGINEER FURTHER TO THE CORRECT SIZE !

 

THIS TRIM OF BRUSH SEALS A GAP OF SIZE FROM  0 – 13 MM

 

THIS UK MADE PRODUCT IS USED BY THE DOOR REPAIR AND GLAZING INDUSTRY


   

IF YOU NEED OTHER SIZES PLEASE ASK, OTHER TRIMS ON OUR CULLEY_FAMILY_SHOP


This correctly made brush strip is not an import; this is made in the UK with pride

 

We make a full fill brush with the right components. This is our 4 mm series backing width brush

 

Our brushes are made of nylon 6 an important factor we feel.

For the technically minded , Nylon 6 is a harder wearing material against concrete, than polypropylene, Nylon 6 has a higher working temperature of about 145 degrees centigrade Dry heat. It can go higher.

Polypropylene softens at 70 – 80 degrees centigrade. A temperature your garage door reaches when it gets warm in the summer , polypropylene bristles then bend and stays bent at the end of a hot summer's day , causing the brush to appear to move away from its opposing surface,ie a gap....!  I will leave you to decide which is the right choice , I will say chalk and cheese!  

 

The carrier is made from 


Architectural aluminium a point worth noting, it makes the carrier stronger, its overall height of the flat part of the h holder is 16 mm, the trim of brush is 15 mm out of the steel backing inside the aluminium on this sizing giving about 13 mm of bristle out of the aluminium holder.

 


(A lot of competitors use this and also partial fill! to make brushes lower in cost for them!)

 

The brush strip should only be fitted to the outside of an up and over door , as the rear of the up and over door dips slightly upon lifting , if you put a brush or any seal on the bottom ,it will catch and scrape causing the door to judder on opening , a problem if you have motor driven doors, and the motors life will be less.

Also fitting our brush strip on the outside gives a further important benefits; you are not creating a dirt and insect trap in front of the door to blow in when the door is lifted.

 

This item is suitable for draught proofing , dust  sealing , dust sealing , insect sealing , stops flies , stops moths , cock roaches yes they are in the UK, ,aluminium,timber ,steel , PVCu, GRP  doors,

 

Cuts easily with top hardened cutters, or good pincers and junior hacksaw,comes with full fitting instructions, you need to follow the full instructions 

 

EVERY DOOR VARIES,WE DO NOT SUPPLY SCREWS AS WE KNOW DIFFERENT SURFACES REQUIRE DIFFERENT FIXINGS AND DIFFERENT COLOURS, AGAIN WE DO NOT DRILL THE PRODUCT AS ALL THE HOLES WILL NOT LINE UP WITH YOUR DOOR.


 

(We have also developed the seal to go up the sides of an up and over door as well look on our shop look for the hairy worm with the best adhesive in the uk )

 

Culley’s also stock a large range of other style draught excluders, brush strips & weather strip products and also trade rubber extrusions. WE ALSO SELL OFF CUTS AT CERTAIN TIMES.

 

Please enquire:  via e bay with your questions for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.

DON’T HEAT THE STREET, SAVE IT!!! ITS YOUR MONEY 


Share this Product


More from this collection