Nylon brush strip, between 10mm - 50mm length trim. Suitable for house doors or garage doors in multiples.

Regular price £8.99 Sale

Regardless of the number of pieces you buy, this product is shipped by a carrier called MYHERMES. They take about 3-5 working days from despatch. For old customers...

Unavailable

George Culley / The Hairy Worm

£8.99
The Hairy Worm

Regardless of the number of pieces you buy, this product is shipped by a carrier called MYHERMES. They take about 3-5 working days from despatch.
For old customers it is now too long to go by post at an economical rate!

We are able to ship this item only to British post codes.

Our brush is made from genuine nylon 6 bristles only to full fill!
We don’t sell brush with a few hidden features.
We don’t sell polypropylene filaments.
We don’t part fill our brushes.

We do sell proper engineered British brush!

Draught proof now before winter keep all the mice out.
Seals by Culley, called thehairyworm premier strip.

These are made and supplied at 890 mm long (in old money, the size is 35 inches or 2 ft 11")

We make them this length to allow you to easily trim these to the correct sizes to suit your door, multiple lengths can be used side by side with little loss of sealing benefit.

(whilst this range seal up to 48 mm, we do make bigger premier strip and make a thicker industrial range from 25 to 150 mm).

Please choose the correct size brush
10 mm size is for fine draught proofing from 0 - 8 mm gaps (we also make smaller seals)
15 mm size is for fine draught proofing from 0 - 13 mm gaps
22 mm size is for fine draught proofing from 0 - 20 mm gaps
30 mm size is for fine draught proofing from 0 - 28 mm gaps
35 mm size is for fine draught proofing from 0 - 33 mm gaps
50 mm size is for fine draught proofing from 0 - 48 mm gaps

Tip: you may have a worn stone step 50 mm is a good answer to this problem.

We can go bigger, please ask.

This is a UK made product and is used by door repair companies and general industry

Garage doors: this can be made into a kit by buying more 890 mm lengths. It can still go by the economical route of: MYHERMES
Subject to the number of lengths it will fit down the bottom of an up and over garage door on the outside, we suggest this because if you fit a brush on the front of a garage door as you lift the door (or the motor lifts a door) the filaments pull off the floor, if you fit it on the rear of the garage door, the brush is further swept tightening into the floor , straining all the door and also if fitted your motor. The other point is any rubbish blown under your door is blown into the garage.

i.e. Buy 3 pieces @ 890 mm down the bottom of an up and over garage door) with this kit it will seal from 2.00 metres up to 2.670 metres , (6 feet to 8 feet 9 “ wide ).

I.e. Buy 4 pieces @ 890 mm down the bottom of an up and over garage door) with this kit it will seal from 2.00 metres up to 3.560 metres, (9 feet to 11 feet 8" wide ) and so on........

It is easy to fit, just follow the simple instructions included, then thehairyworm will give you a long life.

If you need other sizes please ask.

This correctly made brush strip is not an import; this is made in the UK with pride

Materials:
We make a full fill brush with the right components. This is our 4 mm series backing width brush. Our brushes are made of nylon 6 an important factor we feel.

The carrier is made from architectural aluminium a point worth noting, it makes the carrier stronger, its overall height of the flat part of the "h" holder is 16 mm, the trim of brush is measured out of the steel backing inside the aluminium on this sizing giving about 2 mm of bristle less on all sizes out of the aluminium holder.

For the technically minded:
Nylon 6 is a harder wearing material against concrete and other hardwearing surfaces than polypropylene.
Nylon 6 has a higher working temperature of about 145 degrees centigrade, polypropylene softens far earlier than this.
We do not use polypropylene but competitors do, it softens at 70 – 80 degrees centigrade. This is a temperature your garage door reaches when it gets warm in the summer, when warm polypropylene bristles then bend and stays bent causing the brush to appear to move away from its opposing surface, as they cool they stay the same size curled not touching the opposite side.
I will leave you to decide which is the right choice, I will say chalk and cheese!

(a lot of competitors use this and also partial fill! To make brushes lower in cost for them! We don’t short change.)

The brush strip should only be fitted to the outside of an up and over door , as the rear of the door dips slightly upon lifting , if you put a brush or any seal on the bottom ,it will catch and scrap causing the door to judder on opening , a problem if you have motor driven doors.

This item is suitable for draught proofing , dust sealing , dust sealing , insect sealing , stops flies , stops moths , cockroaches yes they are in the UK, aluminium, timber, steel, pvcu, grp doors.

Cuts easily with top hardened cutters, or good pincers and junior hacksaw, comes with full fitting instructions, you need to follow the full instructions.

We do not supply screws as we know different surfaces require different fixings and different colours, again we do not drill the product as all the holes will not line up with your door.

We have also developed and have on sale "thehairyworm" seal to go up the sides of an up and over door, please look on our shop.

Culley’s also stock a large range of other style draught excluders, brush strips & weather strip products and also trade rubber extrusions.

Please enquire: For correct advice for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.
Don’t heat the street, save it!!! It’s your money.

Returns Policy

You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).

You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).

If you need to return an item, simply login to your account, view the order using the 'Complete Orders' link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.

Shipping

We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.

When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.

Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.