We supply this part in 2 off pieces so the item can be COURIERED BY MY HERMES to any UK postcode EXCL SCOTTISH ISLES AND CHANNEL ISLANDS
A 7 FOOT LENGTH SPLIT INTO 2 PARTS ( 2@1067 mm ) KIT ,THIS IS TO GET IT SENT BY MY HERMES
WE HAVE A LOT OF STOCK BUT WE ENGINEER FURTHER TO THE CORRECT SIZE , ALSO OFFERING ANY LENGTHS SUBJECT TO CARRIAGE ! WORTH THE WAIT FOR QUALITY PRODUCT
IF YOU NEED THE BRUSH QUICKER , OR YOU NEED HELP PLEASE ALSO RING 0161 622 0020 11 AM-7 PM M-F
THIS TRIM OF BRUSH SEALS A GAP OF SIZE FROM 0 – 12 MM
THIS UK MADE PRODUCT IS USED BY THE DOOR REPAIR AND GLAZING INDUSTRY
THIS PRODUCT (SUBJECT TO SIZING (BELOW) WILL FIT DOWN THE BOTTOM OF AN UP AND OVER GARAGE DOOR ) WITH THIS KIT IT WILL SEAL FROM 1900 MM UP TO 2140 MM, (7 FEET )
IF YOU NEED OTHER SIZES PLEASE ASK, OTHER TRIMS ON OUR CULLEY_FAMILY_SHOP
This correctly made brush strip is not an import; this is made in the UK with pride
We make a full fill brush with the right components. This is our 4 mm series backing width brush
Our brushes are made of nylon 6 an important factor we feel.
For the technically minded , Nylon 6 is a harder wearing material against concrete, than polypropylene, Nylon 6 has a higher working temperature of about 165 degrees centigrade Dry heat. It can go higher.
Polypropylene softens at 70 – 80 degrees centigrade. A Summer temperature your garage door reaches when it gets warm in the summer , bear in mind you could cook eggs on it when hot , polypropylene bristles then bend and stays bent at the end of a hot summer's day ,damaged and cooling bent , causing the brush to appear to move away from its opposing surface,ie a gap....! I will leave you to decide which is the right choice , I will say a big piece of chalk and a smaller piece of good cheese!
The carrier is made from
Architectural aluminium a point worth noting, it makes the carrier stronger, its overall height of the flat part of the h holder is 16 mm, the trim of brush is 15 mm out of the steel backing inside the aluminium on this sizing giving about 13 mm of bristle out of the aluminium holder.
We supply this part in 2 off pieces @ 1067 mm long so the item can be COURIERED to any UK postcode EXCL SCOTTISH ISLES AND CHANNEL ISLANDS
(A lot of competitors use polypropylene and also partial fill! to make brushes lower in cost for them!)
We supply only full fill brushes
The brush strip should only be fitted to the outside of an up and over door , as the rear of the door dips slightly upon lifting , if you put a brush or any seal on the bottom ,it will catch and scrap causing the door to judder on opening , a problem if you have motor driven doors.
Also fitting our brush strip on the outside gives a further important benefit; you are not creating a litter , dirt and insect trap in front of the door to blow in when the door is lifted.
This item is suitable for draught proofing , dust sealing , dust sealing , insect sealing , stops flies , stops moths , cock roaches yes they are in the UK, aluminium,timber ,steel , PVCu, GRP doors,
We have also developed the seal to go up the sides of an up and over door as well look on our shop The Hairy Worm Seal.
DO NOT CUT TOGETHER ~ CUT CARRIER & BRUSH CORRECTLY
Premier Strip Brush cuts easily with top hardened cutters, or good pincers and junior hacksaw for the aluminium ,comes with full fitting instructions, you need to follow the full instructions
EVERY DOOR VARIES,WE DO NOT SUPPLY SCREWS AS WE KNOW DIFFERENT SURFACES REQUIRE DIFFERENT FIXINGS AND DIFFERENT COLOURS, AGAIN WE DO NOT DRILL THE PRODUCT AS ALL THE HOLES WILL NOT LINE UP WITH YOUR DOOR.
Culley’s also stock a large range of other style draught excluders, brush strips Foam Seals & weather strip products and also trade rubber extrusions. WE ALSO SELL OFF CUTS AT CERTAIN TIMES.
Please enquire: via e bay with your questions for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.
DON’T HEAT THE STREET, SAVE IT!!! ITS YOUR MONEY