Call - 0161 622 0020
Cart 0
QUALITY NYLON BRUSH STRIP 35 -50 MM SUITABLE FOR SHOP OR LIGHT INDUSTRIAL DOORS

QUALITY NYLON BRUSH STRIP 35 -50 MM SUITABLE FOR SHOP OR LIGHT INDUSTRIAL DOORS

£10.78


DRAUGHT PROOFING BRUSHES IN OUR 5 MM SERIES BRUSHES 
 
Check out ALL my other items!    IN THE CULLEY_FAMILY_SHOP

 

Regardless of the number of pieces you buy , this product is shipped by a carrier called MYHERMES They take about 3-5 Working days from time of despatch, SO PLEASE ALLOW THE TIME FOR SHIPPING

 

if you are having a food inspection and need it quick OR IF YOUR ORDER IS A PANIC PLEASE RING 0161 622 0020 AND ARRANGE TNT , IT STILL TAKES 2-3 WORKING DAYS TO GET READY FOR DESPATCH

 

IF THE WEATHER TURNS , PLEASE BEAR IN MIND DOZENS OF PEOPLE ONLY NOTICE DRAUGHTS WHEN IT GETS COLD AND THE HEATING IS CRANKED UP , WE DO GET BUSY , SO THERE COULD BE DELAYS  

 

We are able to ship this item only to MAINLAND British Post Codes

 

OUR BRUSH IS MADE FROM GENUINE NYLON 6 BRISTLES ONLY TO FULL FILL,~MY STANDARD !

WE DONT SELL BRUSH WITH A FEW HIDDEN FEATURES 

WE DONT SELL POLYPROPYLENE FILAMENTS

WE DONT PART FILL OUR BRUSHES

 

WE DO SELL PROPER ENGINEERED BRITISH BRUSH FINISHED IN ROCHDALE , "THE HOME OF THE COOP"  !

 

OUR SMALLER  4 MM  BRUSHES ELSE WHERE TRY 3211 9449 4243 type no gaps 

 

Draught Proof now before winter,  Keep all the MICE out !

 

Seals by Culley's, called The Hairy Worm Industrial Premier Strip

  

These are made and supplied at ANY CUT LENGTH TO ORDER  EXCL CHANNEL ISLES , OUTER ISLANDS.

 

up to 1100 mm these can go budget hermes , above this length TNT EXPRESS is only option

 

We make them these cut length to allow you to easily trim these to the correct sizes to suit your door, Multiple lengths can be used side by side with little loss of sealing benefit. When fitting under the soffit against a roller shutter , it is easier handling metre or so pieces so you are not swinging something too big at height particularly in the wind at height   ! 

 

Tip whilst on about shutter doors , get the maximum gap with the door in a closed position to seal against an outer lath, if it goes in you may need to pack the brush out to get the best seal , or a lot of pressure is added to the door when opening and closing the door. 

 

(Whilst this range seal up to 50 mm, we do make bigger Industrial Premier Strip and make a thicker industrial range from 25-150 mm in 8 mm backing and 11 mm backing for bigger brushes 125 to 300 mm, MADE TO ORDER ONLY AT THOSE SIZES ) 

IN BULK WE CAN ALSO SUPPLY 3000 MM LENGTHS (MAXIMUM) MADE TO ORDER , PHONE 0161 622 0020

 

PLEASE NOTE WE DO NOT SELL 6 MM BACKING BRUSHES AND PASS THEM OFF AS 8 MM , ANOTHER TRICK I'VE SEEN RECENTLY  

 

Please choose the correct size brush

25 mm size is for fine draught proofing from 0 - 24 mm gaps (we also make smaller seals)

35 mm size is for fine draught proofing from 0 - 33 mm gaps

50 mm size is for fine draught proofing from 0 - 47 mm gaps

75 mm size is for fine draught proofing from 0 - 70 mm gaps

100 mm size is for fine draught proofing from 0 - 90 mm gaps

 

 

TIP: You may have a worn stone step IN A CHURCH OR OLDER HOME  50 mm is a good answer to this problem 

 

WE CAN GO BIGGER , PLEASE ASK

 

 

 

THIS IS A UK MADE PRODUCT AND IS USED BY DOOR REPAIR COMPANIES AND GENERAL INDUSTRY

 

 

 

Garage doors & iNDUSTRIAL DOORS  : this can be made into a kit by buying more lengths. It can still go by the economical route of: MYHERMES COURIER, THEY take 3-5 working days , please dont kick us , we are just trying to get it to you in the lowest cost way 

 

Subject to the number of lengths  25 - 50 mm it will fit down the bottom of an up and over garage door on the outside, these are bigger , more dense than our domestic range 

we suggest this because if you fit a brush on the front of a garage door as you lift the door (or the motor lifts a door) the filaments pull off the floor, if you fit it on the rear of the garage door , the brush is further swept tightening into the floor , straining all the door and also if fitted your motor. The other point is any rubbish blown under your door is blown into the garage.

 

 

It is easy to fit , just follow the simple instructions included , then THEHAIRYWORM Will give you a long life.

 

 IF YOU NEED OTHER SIZES PLEASE ASK, OTHER TRIMS ON OUR CULLEY_FAMILY_SHOP

  

 

 

This correctly made brush strip is not an import; this is made in the UK with pride

 

 

 

MATERIALS:

We make a full fill brush with the right components. This is our 5 mm series backing width brush  Our brushes are made of nylon 6 Filaments an important factor we feel.

 

The carrier is made from architectural aluminium a point worth noting, it makes the carrier stronger, its overall height of the flat part of the "h" holder is 24 mm, the trim of brush is measured out of the steel backing inside the aluminium on this sizing giving about 2 mm of bristle less on all sizes out of the aluminium holder.

 

For the technically minded:

Nylon 6 is a harder wearing material against concrete and other hardwearing surfaces than polypropylene 

Nylon 6 has a higher working temperature of about 165 degrees centigrade, Polyproylene softens far earlier than this.

We do not use Polypropylene but competitors do , it softens at 70 – 80 degrees centigrade. This is a temperature your garage door reaches when it gets warm in the summer , when warm polypropylene bristles then bend and stays bent causing the brush to appear to move away from its opposing surface, as they cool they stay the same size curled not touching the opposite side 

I will leave you to decide which is the right choice , I will say chalk and cheese!  


(A lot of competitors use this and also partial fill! to make brushes lower in cost for them! OR SOME ARE NOW SELLING SAME SIZE CARRIER BUT ONLY 4 MM BRUSH PASSING IT OFF AS 5 MM , THEY ARE SELLING WITH AT LEAST 20% LESS FILL , BUT FROM ABOVE THEY LOOK THE SAME

 

 We dont short change.

 

The brush strip should only be fitted to the outside of an up and over door , as the rear of the door dips slightly upon lifting , if you put a brush or any seal on the bottom ,it will catch and scrape causing the door to judder on opening , a problem if you have motor driven fitted doors.

 

 

 

 

This item is suitable for draught proofing , dust  sealing , dust sealing , insect sealing , stops flies , stops moths , Birds cockroaches yes they are in the UK, aluminium,timber ,steel , PVCu, GRP  doors,

 

 

 

 the brush needs cutting away from the aluminium Cuts easily with small bolt cropper style top hardened cutters, and a good hacksaw, 

comes with full fitting instructions, you need to 

follow the full instructions 

 

WE DO NOT SUPPLY SCREWS AS WE KNOW DIFFERENT SURFACES REQUIRE DIFFERENT FIXINGS AND DIFFERENT COLOURS, AGAIN WE DO NOT DRILLTHE PRODUCT AS ALL THE HOLES WILL NOT LINE UP WITH YOUR DOOR.

 

 

We have also developed and have on sale "thehairyworm" 4 mm to 20 mm seal to go up the sides of an up and over door ,please look on our shop item no 3211 9355 3721 ~ CHECK THIS new item OUT ,1000's sold on EBAY already! 

 

Culley’s also stock a large range of other style draught excluders, brush strips & weather strip products and also trade rubber extrusions.

 

 

 

Please enquire:  Via e bay questions OR RING 0161 622 0020 IF YOU NEED FREE HELP (NO EXPENSIVE PHONE CALLS )

For correct advice for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.

 

 

DON’T HEAT THE STREET, SAVE IT!!! 

ITS YOUR MONEY 

If you require more info please contact me on: 0161 622 0020


Share this Product


More from this collection